Видео

Start slowly with 1 finger and then keep adding till it's as stretched as you want. Wait.... What?

Your video was very very helpful. Thank you so much!

Thanks mr.

Awesome video! I found this after I took my Riptide apart and figured out my issue (the set screw tying the cup magnet to the motor shaft was completely loose), but this has more info than the rest of the internet. Thank you!

That lubricant is finally what did it for me. I tried heating it (which made it too soft) and the 45 degree angle trick, but after seeing this video added some food grade lubricant and just a bit of heat and the 45 degree angle trick and that did it? Thanks a bunch.

Your suggestion was great. I use oil inside the rubber tube and on the nozzle. The rubber pipe very easily fits into the nozzle. Actually, rubber pipe was less in the diameter as compared to nozzle. Thanks.

I haven’t been able to get to the other function pages on the main control screen using supplied instructions. Specifically, I want to change from C° to F° on F13. Can you explain the sequence for getting the function pages beyond F1-F4? Thanks

Slick!

I just got the parts needed to experiment with closed transfers, and how to add fining agents was a question that had just occurred to me. Here's the answer before I even got a chance to ask!

Are these available in 1"? Looking for 1" tube with 1" female cam on one end and 1" male cam on the other.

Hey Bobby, this is Charlie from Texas and I have a question. I have a kid 15.5 gallon and I am trying to put a Farrell for my email limit I need to know what size Ferrell I need for a 5500 W elephant? This is my first pop. I’m trying to make thanks

This was very helpful. Thank you!

@brewhardware you’re 8 minutes from my office. I’ll be in there soon 😄👍🏼

Thanks Bobby!

Nice to see this channel active again!

Nice, innovative and needed accessory! Your site currently says for 15 and 22 gallon kettles. Is the 22 supposed to be 20? If so, I will be adding one of these decals for my 20 gallon kettle to my next BrewHardware order. Thanks Bobby!

Oh, that cart's getting bigger.... Thanks, Bobby.

You shouldn’t wear stripes on video

Thanks for the video. My riptide wasn't working and this video fixed my issue!

Great video. You've convinced me to have a couple of pots welded at the local shop.

Great idea would like to try the faire on the out side and then fusion tig weld???

I just made my own with an airlock, some tubing and an old camping collapsible water container. Fill it with CO2 from the tank, then swap the airlock when cold crashing.

This video helped me very much thank you

I've got 12mm OD hose pipe fittings & 10mm OD fittings on a 3 Port Oil Catch Can & would 10mm OD Silicone Vacuum Hose will it Stretch over the 12mm OD hose pipe fittings that are on the PCV Valve & the other 2 12mm OD hose fittings one on the manifold & the other on the other rocker cover on a PT Cruiser as I have a Blow By Problem & having 3 Port Oil Catch with filter & I know that I don't have much room to put this 3 Port Oil Catch with filter but my son Brannon has a 3D Printer & he is going to make a special mounting bracket for me so I can mount this 3 Port Oil Catch Can with filter no problem at all & also has a drain tap at the bottom of the Catch Can Kind Regards Peter & I'm sure that 10mm 0D Silicon Vacuum Hose should Stretch over the 3 X 12mmOD Hose Fittings & had tried the vinyl clear rubber 10mm OD hose & managed to heat up the hose first from boiling water & then & force the hose over the 12mm OD hose pipe fitting & I did the the same way as you did Sir by putting the 12mm OD hose pipe fitting on an angle & turned the 10mm OD hose around & got it on the 12mm OD fitting & it was hard going but I got there & I'm sure the 10mm Silicone Vacuum Hose should stretch over the 12mm OD hose pipe fittings a lot easier than vinyl rubber clear hose

What flux and soldier did you use?.

I have a BrewBuilt IceMaster Max2. Would you be able to mod that for heating? If so, what would the cost be?

I bottle with roughly 3 to 4 oz of priming sugar. Does the CO2 go into solution and if so does that create a potential over carbonation issue?

HOLA BUEINA EQUIPO PARA HASER CERVEZA 🍻

ХОРОШИЙ ОХЛАДИТЕЛЬ У МЕНЯ НА ПИВОВАРНИ ТАКОЙЖЕ👍🏻

Merci beaucoup pour cette démonstration très bien faite. Les arguments positifs et négatifs sont bien définis. Cela m'a beaucoup aidé. Thanks a lot for all the detailed explanattion. Thevp pro and con have been seen. You really help me.

Pulling through on a beer keg is a heck of a lot tougher than with a pot. I went with a 35mm hole and stretched to fit. (inner diameter of the ferrule). I will probably go 37mm next time around. Make sure you are using real wrenches (not adjustable) to tighten (adjustable will slip and round the nut) and you will likely need an extender bar if you aren't young and strong. I used the stainless pipe from inside the keg to give me the added leverage. Another hint. You can get long 1.5" ferrules. This gives you lots of meat both on the inside and outside.

Thank you for the video. I just boiled some water and dipped the end of the tube in for 5-10 seconds and went and connected it just fine. Could always add a clamp if needed.

thanks for just saving someone who has no idea. :) All the best

you should add your urls to the description, you will get more conversions for sales. otherwise great tool and good video! thanks

My brew kettle/pot doesn't have any openings whatsoever. It's just a stainless steel pot. I want to use the camlock fittings (based on his recommendations). Unfortunately I don't know where to begin! Do I need a bulkhead if I plan on using a camlock fitting? Also, what about the thermometer? I don't have one for my brew kettle, nor does my pot have an opening for it. Can someone please help me???

brewhardware, what aboit when we try to push one silicon part over another silicon part ?

How can we sanitize the inflatable vessel ?

Doesn't work with rubber hose so please dont waist ur time

What was the garden hose type fitting called cool touch? I'm having issues finding them.

I actually reinvented this stuff without knowing this product, lmao. I use a wine bag-in-box bag, I don't have the one-way valve but it seems to work either way

Nice job! I like this method since it seems more sanitary!

Would this work with a twin walled insulated pot ?

I didn't see any things n the site to buy some of these parts. Please reply with the site to contact

Thank you.

For 3kw element, what cable and plug do you recommend?

Ty for this tip. You helped an military aircraft mechanic get the job done.

It was a good video. Lots of knowledgeable information. Perhaps one on controllers now?

Fixed my 30-year-old March pump in about 15 min. Thanks for the video. It was a big help.

Does the start/run capacitor under the motor ever need to be replaced? Pump runs but its noisy .